！Before installation, confirm that：
This high-performance component does not comply with the laws and regulations for highway driving and cannot be used on any vehicle that has been registered or certified for use on highways. This means that the component may only be suitable for racing cars or other off-road vehicles. If it is installed on vehicles driving on the highway, legal issues will be borne by oneself.
This is the installation process for the DP-0291: 2007.5-2012 6.7L Dodge Ram Cummins 2500/3500 4" DPF Delete Race Pipe,provided for your reference during installation.
Step 1:
Remove all sensors and DEF injector connections from the downspout, SCR, and diesel particulate filter.
Step 2 :
Unscrew the two flange connections and loosen the clamp on the exhaust pipe end. Remove the SCR and DPF from the truck, and then continue to remove the exhaust tailpipe. At the turbocharger, loosen the bolt to match the clamp and remove the clamp that secures the drain pipe.
Step 3 :
Use a flat head screwdriver to pry out the clamps from three positions on the flange. Remove the water pipe and keep the clip as it will be reused.
This high-performance component does not comply with the laws and regulations for highway driving and cannot be used on any vehicle that has been registered or certified for use on highways. This means that the component may only be suitable for racing cars or other off-road vehicles. If it is installed on vehicles driving on the highway, legal issues will be borne by oneself.
This is the installation process for the DP-0291: 2007.5-2012 6.7L Dodge Ram Cummins 2500/3500 4" DPF Delete Race Pipe,provided for your reference during installation.
Remove all sensors and DEF injector connections from the downspout, SCR, and diesel particulate filter.
Unscrew the two flange connections and loosen the clamp on the exhaust pipe end. Remove the SCR and DPF from the truck, and then continue to remove the exhaust tailpipe. At the turbocharger, loosen the bolt to match the clamp and remove the clamp that secures the drain pipe.
Use a flat head screwdriver to pry out the clamps from three positions on the flange. Remove the water pipe and keep the clip as it will be reused.
Step 4:
Before installing pipes and mufflers, make sure to place pipe clamps on all connections.Install #1 turbo pipe using the stock turbo bond clomp. Snug the clamp down so it will hold pipe but pipe con still be moved.Step 5:
Install pipeline 2 and connect it to the end of # 1,Sensors/pipes do not need to be plugged into the exhaust system.Step 6:
Using the provided safety torx tool, transfer the MAF sensor from the factory intake port to the new intake port, and then tighten the intake bracket by hand.Step 7:
Tighten the turbine connecting pipe, start working from the front pipe, connect the pipe to the block connection, tighten the pipe (Note: For increased safety, omig welding should be applied to the clamping connection of the pipeline), Do not weld the pipe clamp.Related installation manual：
2009-2019 6.7L Dodge Ram Cummins Coolant Bypass Barb Leak repair Adapter Kit
2009-2019 6.7L RAM Cummins Coolant Hose Barb Adapter Leaking Repair Kit
2007-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel 3.5inch High Flow Intake Manifold Elbow Tube Horn
2007-2009 6.7L Dodge Ram Cummins Diesel EGR Delete Kit
2010-2012 6.7 Dodge Ram Cummins 4" Turbo-Back DPF Delete Pipe
2007-2024 6.7L Dodge Ram Cummins EGR Throttle Valve Delete Kit
2007.5-2024 Dodge Ram 6.7L Intake Air Temperature Sensor Extension Harness Diesel
2009-2024 6.7L Ram Cummins 2500 3500 EGR Valve Cooler Delete Kit
2007.5-2018 6.7L Dodge Cummins 2500 3500 CCV Black Crankcase Ventilation Diesel
2010-2024 6.7L Ram Cummins 2500 3500 EGR Valve Cooler Delete Kit
2006-2024 5.9L/6.7L Dodge Ram Cummins Billet Valve Cover
2010+ Dodge Ram Cummins EZ-Lynk/CCV SOTF Switch
2007.5-2012 6.7L Dodge Ram Cold Air Intake w/Filter
Last edited:
